Attach the cables required between the video encoder and the camera, then configure the video encoders settings.
Hardware connections:
Hardware connections:
Sony EVI-HD1 - surveillance camera overview and full product specs on CNET. Holiday Gift Guide 2020. Best gifts under $30. Download Sony Visca Driver EVI-D30/EVI-D31 for free. Controller for Cameras with the Visca protocol. (example Sony EVI-D30/31) Pan, tilt, and zoom camera with absolute or relative positioning.
- Connect the video from the camera to the video encoder. On the back of the EVI-D30/31 there is an area labeled “OUT”. Underneath “OUT”, one of the RCA jacks is labeled “VIDEO”. Connect a RCA cable from this to one of the video encoder’s open video in ports. You may need to use an RCA to BNC converter on the side of the cable that is being connected to the 2400/2400+.
- Connect the VISCA cable from the COM1 serial port on the 2400/2400+ to the VISCA IN port on the back of the EVI-D30/31.
- Next, configure the camera ID on the EVI-D30/31. On the back of the EVI-D30/31, above “OUT” there is an area labeled ‘CAMERA NO.’ witch you can set to 1.
Video Encoder Configuration:
Note this section of configuration is firmware version specific.
AXIS 2400/2401 firmware version 2.xx and AXIS 2400+/2401+ firmware version 3.xx:
- Bring the web interface of the AXIS 2400/2400+ up in a browser window.
- Click the admin button to enter the administration pages on the video encoder.
- Click the icon labeled ‘COM1’ and change the following settings:
- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button
- Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’
- Set ‘Drivers for Pan Tilt’ to ‘Sony EVI-G20/G21/D30/D31’
- Click ‘Save’
- Click ‘Save’
- Next click the icon for the video input the EVI-D30/31 is attached to
- Set ‘Pan Tilt Serial Port’ to ‘Sony - EVI-G20/G21/D30/D31’
- Click the ‘Driver Specific Settings’ button
- A new browser window will launch to display the parameters.
- Change ‘Camera X has ID’ to ‘no 1’.
- Click the ‘Driver Specific Settings’ button
- A new browser window will launch to display the parameters.
- Change ‘Camera X has ID’ to ‘no 1’.
Evi D30 Drivers For Macbook
- Set the drop down box to the right of ‘no 1’ to ‘D30/D31’
- Click ‘Apply’
- Click ‘Close’
- Click ‘Apply’
- Click ‘Close’
- That will complete the PTZ setup.
AXIS 2400/2401 firmware version 1.xx:
- Bring the web interface of the 2400 up in a browser window.
- Click the admin button to enter the administration pages on the 2400.
- Click the icon labeled ‘COM1’ and change the following settings:
- Set ‘Purpose’ to ‘Pan Tilt’
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button
- Set ‘Interface Mode’ to ‘RS232’
- Set ‘Baud Rate (bps):’ to 9600
- Set ‘Data Bits:’ to 8
- Set ‘Stop Bits:’ to 1
- Set ‘Parity Bit’ to None
- Click the ‘Save’ button
- Next click the icon labeled ‘Pan Tilt’ located below the icon for ‘COM1’
- Set ‘Drivers for Pan Tilt’ to ‘Sony D30/D31’
- Click ‘Save’
- A new window will appear titled ‘Specific parameter for Sony D30/D31’.
- Change the ‘Camera X is connected to ID’ to ‘ID no 1’ than click 'Apply' and 'Close'.
- Click ‘Save’
- A new window will appear titled ‘Specific parameter for Sony D30/D31’.
- Change the ‘Camera X is connected to ID’ to ‘ID no 1’ than click 'Apply' and 'Close'.
- Next click the icon for the video input the EVI-D30/31 is attached to
- Set ‘Pan Tilt Serial Port’ to ‘COM1 – Sony D30/D31’
- Click Save
- Click Save
- That will complete the PTZ setup.
Evi D30 Drivers For Macbook Pro
Skyrim se add perk points mod.
Troubleshooting:
If the EVI-D30/D31 will not PTZ then try the following:
Troubleshooting:
If the EVI-D30/D31 will not PTZ then try the following:
- Check the VISCA cable connection to make sure it is secure
- Recheck all the parameter settings.
- Restart the video encoder and try to PTZ again.
- Recheck all the parameter settings.
- Restart the video encoder and try to PTZ again.
Evi D30 Drivers For Macbook Air
Vote, how useful was this article to you? Wacom download mac.